Standardized management of construction sites, safe and beautiful civilized construction sites are something that every construction site must face. The standard steel bar processing shed on the construction site is one of the protective products in construction safety management. The steel bar processing shed on the construction site generally belongs to order production. The production standards for the steel bar processing shed on the site allow sufficient space and welding equipment for processing and production!

鋼筋加工棚制作要求：在建建筑在10米以上，鋼筋加工場必須設置防護棚，必須設置雙層防砸結構。

Requirements for the production of steel bar processing shed: If the building under construction is more than 10 meters, a protective shed must be set up in the steel bar processing yard, and a double-layer anti impact structure must be set up.

一般是組合式連接，散裝發貨便于運輸。 鋼筋棚的搭設還要注意一下幾點：

Generally, it is a combination connection, which is easy to transport when shipped loose. The installation of the steel shed should also pay attention to the following points:

1.工具式鋼筋加工棚搭設具體尺寸根據現場實際情況確定。

1. The specific size of the tool type steel bar processing shed shall be determined based on the actual situation on site.

2.搭設在塔吊回轉半徑和建筑物周邊的加工車間必須設置雙層硬質防護。

2. The processing workshop set up around the turning radius of the tower crane and the building must be equipped with double layer hard protection.

3.加工車間地面需硬化，宜選用砼地面。

3. The ground of the processing workshop needs to be hardened, and concrete ground should be selected.

鋼筋加工棚制作方法是什么？鋼筋加工棚廠家解析

What is the production method for the steel bar processing shed? Analysis of steel bar processing shed manufacturers

4.加工車間頂部應張掛警示標識和宣傳用語的橫幅，橫幅寬度宜為1m。

4. Safety warning signs and safety propaganda slogans should be hung on the top of the processing workshop, with a width of 1m.

5.工具式鋼筋加工棚需在醒目處掛操作規程圖牌，圖牌的尺寸為：寬×高=2000mm×1000mm。

5. The tool type steel bar processing shed should be prominently hung with an operating procedure diagram board, with a size of: wide × Height=2000mm × 1000mm.

6.各種型材及構配件規格為參考值，具體規格應根據當地風荷載、雪荷載進行核算。 7.南方地區，如遇臺風應采取防風措施，可設置纜風繩。

6. The specifications of various profiles and components are reference values, and the specific specifications should be calculated based on local wind and snow loads. 7. In the southern region, if encountering a typhoon, wind prevention measures should be taken and cable ropes can be set up.

鋼筋加工防護棚制作方法：

Production method of steel bar processing protective shed:

1.構件組裝而成，采用封閉式防護，防護性能高，雙層防護，有效緩沖高空墜落沖擊力。

1. The components are assembled and adopt closed protection, with high safety protection performance and double layer protection, effectively buffering the impact of high-altitude falls.

2.采用國標鋼材制作，堅固牢靠、經久耐用。

2. Made of national standard steel, it is sturdy, reliable, and durable.

3.全自動高溫烤漆，3年日曬雨林不易褪色。

3. Fully automatic high-temperature baking paint, which is resistant to fading in the 3-year sun exposure rainforest.

4.拼裝式，快速組裝，拆卸簡單，方便運輸。

4. Assembly type, fast assembly, simple disassembly, and convenient transportation.

5.款式、顏色、尺寸可根據客戶要求定制；

5. The style, color, and size can be customized according to customer requirements;

6.地面需要硬化，立柱基礎澆筑700*700*700mm混凝土，預埋300*300*12mm鋼板.

6. The ground needs to be hardened, and the column foundation is poured with 700 * 700 * 700mm concrete, and 300 * 300 * 12mm steel plates are embedded

7.各種型材及配件規格可按工地所在地的安防標準定制。

7. Various profiles and accessory specifications can be customized according to the security standards of the construction site.

鋼筋棚的搭設還要注意以下幾點：

The installation of the steel reinforcement shed should also pay attention to the following points:

1. 工具式鋼筋加工棚搭設具體尺寸根據現場實際情況確定；

1. The specific size of the tool type steel bar processing shed shall be determined based on the actual situation on site;

2. 搭設在塔吊回轉半徑和建筑物周邊的加工車間必須設置雙層硬質防護；

2. The processing workshop set up around the turning radius of the tower crane and the building must be equipped with double layer hard protection;

3. 加工車間地面需硬化，宜選用砼地面；

3. The ground of the processing workshop needs to be hardened, and concrete ground should be selected;

4. 加工車間頂部應張掛警示標識和宣傳用語的 橫幅，橫幅寬度宜為1m；

4. Safety warning signs and safety propaganda slogans should be hung on the top of the processing workshop, with a width of 1m;

5. 工具式鋼筋加工棚需在醒目處掛操作規程圖牌，圖牌 的尺寸為：寬×高=2000mm×1000mm；

5. The tool type steel bar processing shed should be prominently hung with an operating procedure diagram board, with a size of: wide × Height=2000mm × 1000mm;

6. 各種型材及構配件規格為參考值，具體規格應根據當 地風荷載、雪荷載進行核算；

6. The specifications of various profiles and components are reference values, and the specific specifications should be calculated based on local wind and snow loads;

7. 南方地區，如遇臺風應采取防風措施，可設置纜風繩。

7. In the southern region, if encountering a typhoon, wind prevention measures should be taken and cable ropes can be set up.

鋼筋加工棚制作方法是什么？鋼筋加工棚廠家解析

What is the production method for the steel bar processing shed? Analysis of steel bar processing shed manufacturers

在建筑施工現場工作，工人們經常需要在現場對各種所需的建筑材料進行加工，為了防止高空落物誤傷作業人員，保障地面加工作業人員的作業，在施工現場會建起防護棚，現有的防護棚的搭建一部分是通過焊接，搭建完成后不易拆卸，拆卸時需要破壞防護棚的一些結構，使鋼筋加工棚不能重復使用，造成經濟浪費，防護棚搭建時耗時長，施工麻煩，現有的防護棚使用時對高空落物的沖擊力不能有效的消減。

At the construction site, workers often need to process various required building materials on site. In order to prevent high-altitude falling objects from injuring workers and ensure the safety of ground processing workers, protective sheds will be built on the construction site. Part of the existing protective sheds are built through welding, which is not easy to disassemble after completion. Some structures of the protective sheds need to be damaged during disassembly, The reinforcement processing shed cannot be reused, resulting in economic waste. The construction of the protective shed takes a long time and is troublesome. The existing protective shed cannot effectively reduce the impact of high-altitude falling objects when used.

本文由鋼筋加工棚為您提供，我們的網站是:http://novirus365.cn我們將以全心全意的熱情為您提供服務，歡迎您的訪問！

This article is provided by the steel bar processing shed, and our website is: http://novirus365.cn We will provide you with wholehearted enthusiasm and welcome your visit!